Grip Warmer Kits for Harley Davidson Motorcycles
Description:
- These new kits are complete with everything you need to install your grip warmers. Kit includes a 4 level power controller with a adjustable intensity LED's, 2 heater inserts, hardware and wire threading tool. Not to be used with aluminum handlebars. Fast and easy installation. Use the grips of your choice. These two part numbers fit most Harley Davidson motorcycles. Available with chrome or black power controller.
- With black controller (#SY-210046)-----$109.95
- With chrome controller (#SY-210045)-----$129.95
Grip Warmer Kits for Motorcycles
Description:
- These new kits are complete with everything you need to install your grip warmers. Kit includes a 4 level power controller with adjustable intensity LED's, 2 heater inserts, hardware and wire threading tool. Not to be used with aluminum handlebars. Fast and easy installation. Use the grips of your choice. These two part numbers fit most motorcycles other than Harley Davidson. Available with chrome or black power controller.
- With black controller (#SY-210064)-----$109.95
- With chrome controller (#SY-210063)-----$129.95
Custom Heated Motorcycle Grips
Description:
- Black powder coat finish on both ends of grips
- Designed for 1" bars without a blockage in the handlebars
- Wires go through the bars and exit near the bar clamps for wiring into the electrical system
- Includes 3 position switch (high-off-low), electrical connectors, resistor & instructions
- Made in the USA
- Approximately 5 1/4" long, for 1" bars (#ET-CHG-1blk)-----$129.95
Custom Heated Touring Motorcycle Grips
Description:
- Designed for large touring bikes (Gold Wings & similar bikes) with 7/8" bars
- Wires go under the bars along with other control cables and up to the bar clamp area for wiring into the electrical system
- Includes 3 position switch (high-off-low), electrical connectors, resistor & instructions
- Grips are approximately 6 1/4" long
- Made in the USA
- Price (#ET-CHG-5)-----$129.95
Custom Heated Motorcycle Grips
Description:
- Special laced black leather grip with standard chrome ends
- Designed for 1" bars (excluding Harley-Davidsons with air in the left bar)
- For use when either a blockage is in the bar or where you do not want to drill the holes for an internal installation
- Wires go under the bars along with other control cables and up to the bar clamp area for wiring into the electrical system
- Includes 3 position switch (high-off-low), electrical connectors, resistor & instructions
- Grips are approximately 5 1/4" long
- Made in the USA
- Price (#ET-CHG-6ll)-----$129.95
Custom Heated Motorcycle Grips
Description:
- Designed for bars without a blockage in the handlebars
- Wires go through the bars and exit near the bar clamps for wiring into the electrical system
- Includes 3 position switch (high-off-low), electrical connectors, resistor & instructions
- Made in the USA
- Approximately 5 7/8" long, for 7/8" bars (#ET-CHG-7)-----$129.95
Custom Heated Motorcycle Grips
Description:
- Designed for 7/8" bars with wiring under the handlebars
- Wires go under the bars along with other control cables and up to the bar clamp area for wiring into the electrical system
- Includes 3 position switch (high-off-low), electrical connectors, resistor & instructions
- Made in the USA
- Approximately 5 7/8" long (#ET-CHG-8)-----$129.95
Custom Heated Touring Motorcycle Grips
Description:
- Designed for large touring bikes with 7/8" bars
- Wires go through the bars and exit near the bar clamps for wiring into the electrical system
- These CANNOT be used on a standard Gold Wing
- Includes 3 position switch (high-off-low), electrical connectors, resistor & instructions
- Grips are approximately 6 1/4" long
- Made in the USA
- Price (#ET-CHG-9)-----$129.95
Custom Heated Motorcycle Grips
Description:
- Designed for bikes with 1" bars
- Wires go under the bars along with other control cables and up to the bar clamp area for wiring into the electrical system
- Includes 3 position switch (high-off-low), electrical connectors, resistor & instructions
- Grips are approximately 6" long
- Made in the USA
- Price (#ET-CHG-10)-----$129.95
Replacement Foam Covers for Custom Heated Motorcycle Grips
Description:
- Replacement foam covers for: (#ET-CHG-1), (#ET-CHG-2), (#ET-CHG-3), (#ET-CHG-4), (#ET-CHG-6)
- Approximately 4 3/4 inches long
- Installation instructions included
- Price (#ET-FOAM-1)-----$12.99
- Replacement foam covers for: (#ET-CHG-5), (#ET-CHG-7), (#ET-CHG-8), (#ET-CHG-9), (#ET-CHG-10), (#ET-CHG-11)
- Approximately 6 1/8 inches long
- Installation instructions included
- Price (#ET-FOAM-2)-----$13.99
Replacement Resistor for Custom Heated Motorcycle Grips
Description:
- Replacement resistor (ET-CHG-RES)-----$8.99
ATV Heated Grips, Thumb Warmer & 5 Level Control Kit
Description: with 2 zone controller
- Will not work on snowmobiles or other vehicles without a regulated DC power supply
- Fits any 7/8" handlebar
- Easy to install heated grips (no adhesive required) & thumb warmer
- Dual zone temperature control
- Independent control between grips and thumb warmer
- 5 levels of heat, maximum 20 watts @ 14 volts
- LED light level indicators (adjust for evening or daylight)
- 2 hour auotmatic shut off (saves battery power)
- Power level memory
- Multiple mounting options
- Plug & play electrical connections (for easy installation)
- Instructions included
- Made in the USA
- Price (#ET-17-9530)-----$99.95
ATV Heated Grips, Thumb Warmer & 5 Level Control Kit
Description: with 4 zone controller
- Same kit as #ET-17-9530 shown above except this has a four zone controller which allows you to control 4 different accessories such as: heated hand grips, thumbwarmer, seat heater, and vest or foot warmers. Basically it is 4 independent controls sharing one set of display LEDs and set up buttons in a very compact package. Each accessory can be set at any of 5 power levels. Features include memory of your settings after you shut down. Adjustable intensity LED Light. The control only can replace your existing 2 zone without any wiring changes.
- Price (#ET-17-9547)-----$129.95
ATV Heated Grips
Description:
- Fits 7/8" handlebars (not for twist throttles)
- Easy to install heated grips (no adhesive required)
- Wiring & Off-Lo-High switch included
- 5 1/4" long grips
- Price (#N-012694)-----$63.98
Heated ATV, Snowmobile & Motorcycle Hand Grips
Description:
- Requires a 12 volt system capable of powering a headlight
- Two molded Kraton thermoplastic rubber grips
- Low-Off-High control switch and resistor
- Simple instructions
- Black for ATV/snowmobile 7/8" bars (#)-----$54.99
- Red for ATV/snowmobile 7/8 bars (#)-----$54.99
- BLUE for ATV/snowmobile 7/8 bars (#)-----$54.99
- Black for motorcycle twist grip, 7/8" bars, 5.25" long (#ET-17-9517)-----$68.99
- Black for motorcycle twist grip, 7/8" bars, 5.75" long (#ET-17-9519)-----$94.99
- Black for motorcycle twist grip, 1" bars, 4.75" long (#ET-17-9518)-----$94.99
- Black for motorcycle twist grip, 1" bars, 5.25" long (#WP-40-4159)-----$94.99
- Replacement high-low-off switch (#ET-74-6067)-----$6.99
- Replacement resistor (#ET-74-6068)-----$7.49
Heated Snowmobile Hand Grips
Hot Grips draw less electrical current than handlebar cartidge heating devices, as the heating element radiates heat from the grip, close to the hands. This results in less heat loss through the steel handlebars, brighter headlight on machines with limited electrical output and faster warm-up.
Description:
- Fits 7/8" handlebar
- Requires a 12 volt system capable of powering a headlight
- Molded Kraton thermoplastic rubber
- Outside grip diameter 1.11"
- Overall grip length 5.14", internal length 4.93"
- Low-Off-High control switch, 8-15 watt
- Simple instructions
- Black (#ML-157)-----------------------------------------$52.49
- Blue (#ML-157B)-------------------------------------------$52.49
- Red (#ML-157R)--------------------------------------------$52.49
- Green (#ET-17-9513)-----------------------------------------$52.49
- Purple (#ET-17-9514)----------------------------------------$52.49
- Replacement grip blue (#ET-74-6071)-----------------$22.99
- Replacement grip red (#ET-74-6072)-------------------$22.99
- Replacement low-off-high switch (#ET-74-6067)-----$7.49
- Replacement resistor (#ML-B1072 ET-74-6068)--------------------$8.19
Heated Snowmobile Hand Grips
With Internal Wiring
Hot Grips draw less electrical current than handlebar cartidge heating devices, as the heating element radiates heat from the grip, close to the hands. This results in less heat loss through the steel handlebars, brighter headlight on machines with limited electrical output and faster warm-up.
Description:
- Newly developed version provides protection for wires
- Wires are fed through the center of handlebar
- Can be used on Arctic Cat and Ski-Doo models that
have wires that feed through the handlebar
- Fits 7/8" handlebar
- Requires a 12 volt system capable of powering a headlight
- Molded Kraton thermoplastic rubber
- Outside grip diameter 1.11"
- Overall grip length 5.38", internal length 4.90"
- Low-Off-High control switch, 8-15 watt
- Simple instructions
- Black (#17-9505)------SOLD OUT
- Blue (#ML-158B)--------$54.95
- Red (#17-9507)---------SOLD OUT
- Green (#17-9508)------SOLD OUT
- Purple (#17-9509)-----SOLD OUT
Handlebar Grip Heater Kit
Description:
- Adhesive grip heater that fits under O.E.M. Grips ATVs (not for Bombadier ATV 2002 or older)
- Fits most Arctic Cat, Polaris, and Ski-Doo snowmobiles (not for Yamaha Snowmobiles)
- Comes with thin adhesive heating element, high-off-low sealed switch, and wire leads.
- For use with any 12 volt 3 amp system, includes easy to follow instructions
- Replaces Polaris P/N 2460247
- Replaces Ski-Doo P/N 410-1072-00
- Complete Kit (#ML-8062)-----$29.99
- Replacement switch (#ML-11-4346)-----$7.20
- Replacement resistor (#ML-11-4347)-----$8.99
- Replacement heating elements (#ML-8062A)-----$18.99 pair
- Note: Not for use on vehicles with twist throttles, such as motorcycles
Snowmobile Thumb Warmer
Description:
- Easily mounted on most all thumb throttles (not recommended for metal throttles)
- Space age technology heater tested at -20 degrees Fahrenheit
- Low electric draw, lots of warmth
- "Latest technology" kit, (mounts on back side) (#ML-11-1577)-----$34.65
- Standard kit, (mounts on thumb side) (#ML-11-4346)-----$24.99
- Replacement low/off/high switch (#ML-11-4346)-----$7.49
- Replacement resistor (#ML-11-4010)-----$7.20
This Site is Copyright © 1999-2008 by Heeters
Performance Center, Inc. All Rights Reserved
Home Page - Motorcycles - Mopeds - Scooters - ATVs - Go-Karts - Snowmobiles - Watercraft - Parts & Accessories - Odds & Ends - Specials - Service |
Return to Top
